LM311N DATASHEET PDF

LM311N DATASHEET PDF

LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Zulkizilkree Nelkree
Country: Kuwait
Language: English (Spanish)
Genre: Science
Published (Last): 25 November 2017
Pages: 240
PDF File Size: 13.43 Mb
ePub File Size: 13.26 Mb
ISBN: 437-7-64442-297-8
Downloads: 32090
Price: Free* [*Free Regsitration Required]
Uploader: Shakami

All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc.

LMN Comparator with Strobe – Discussion Forums – National Instruments

Message 3 of 5. Message 4 of 5.

Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package. Submitted by admin on 6 March Most Active Software Boards: According to the datasheet, if you tie the strobe pin to GND then the output should be disabled. LMN Comparator with Strobe. I tried adding in a transistor with a 1k resistor to ground and a TTL signal at the base datasheft per the datasheet and this doesn’t disable the output either.

The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you.

  INTRODUCTION TO RELATIVISTIC QUANTUM CHEMISTRY DYALL PDF

The simplified schematics of the IC is shown below:. Why is it not working in Multisim?

Multisim and Ultiboard

I built a simple circuit using the LMN comparator. The simplified schematics of the IC is shown below: I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal. Message 5 of 5. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Dayasheet problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. The output is correct as seen on the scope. A sample circuit is shown below in which the Inverting Terminal is set to 2.

TL — Programmable Reference Voltage. I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Vcci. The LM can work on a Single supply voltage or in a dual supply mode.

When not in use the pins 5 and 6 should be shorted as shown above. This pin is connected to the ground of the system Negative voltage can also be used. As grounding unused pins is a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for a ground wired to that pin. You can refer the other possible circuits from lm311b LM datasheet given at bottom.

  HMI GXO 3502 PDF

You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice datasheer.

Texas Instruments/TI LMN/NOPB – PDF Datasheet – Analog Comparators In Stock |

Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. Message 2 of 5. The pins darasheet and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage. If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low.

An Emitter Output Circuit is shown below. Any help is appreciated.

The problem is that the strobe pin is not working for dahasheet model. Could the component model be the issue? Message 1 of 5. Normally these pins are not used since the Input Offset itself is much better controlled.