IEC 61058-1 PDF

IEC 61058-1 PDF

IEC Standard | Switches for appliances – Part Requirements for mechanical switches. This part of IEC applies to switches for appliances. The switches are intended to control electrical appliances and other equipment for. This part of IEC applies to electronic switching devices and shall be used in conjunction with the general requirements of IEC

Author: Temi Dougor
Country: Romania
Language: English (Spanish)
Genre: Career
Published (Last): 10 June 2009
Pages: 201
PDF File Size: 6.6 Mb
ePub File Size: 5.31 Mb
ISBN: 759-7-17072-307-9
Downloads: 72156
Price: Free* [*Free Regsitration Required]
Uploader: Gugis

Secondlya push of 30 N for 1 min is then applied to all actuating members.

Signal indicators, the function of which is independent from the function of the switch, are operated continuously. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.

BS EN 61058-1:2002+A2:2008

Rivets used for current- carrying connections shall be secured against loosening if these connections are subject 610058-1 torsion in normal use. Cartridge, fuse- links tF.

For switches of small dimensions, the marking may be on different surfaces. Shopbop Designer Fashion Brands. Compliance is checked by the humidity treatment described in this subclause, followed immediately by he tests of NOTE 2 Switches submitted in an appliarce may be tested using the circuit in tlie appliance and classified according to 7 1 2 5 as a declared specrfic load.

  JAVED GHAMIDI BOOKS PDF

Where this is not practical on the specimens to be 16058-1 for the test of clauses 16 iecc 17, the test of SXmm Example 2 Condition: Unless otherwise specified, parts connected to a SELV supply not exceeding 24 V are not considered to be live parts. Switches which incorporate additional control functions governed by the switch function are within the scope of this standard, This standard also covers the indirect actuation of the switch when the operation of the actuating member or sensing unit is provided by a remote control or 6058-1 part of an appliance or equipment such as a door.

Fixed capacitors for electromagnetic suppression and connection to the supply mains lEC Protection against overvoltages of atmospheric origin or due to switching lEC Rotating machinery lEC The method of operation is that specified for accelerated speed in As the impulse ; lest voltage of table M. This fourth edition cancels and replaces the third edition published inAmendment 1: Fixing screws for enclosures ic tightened with a torque as specified in table Sealing compound whfch softens in heat provtdes satisfactory locking only.

Amazon Second Chance Pass it on, trade it in, give it a second life. Add to Alert PDF. Click to learn more.

This part of IEC does not apply to devices covered by: For switches for 10 operating cycles according to 7,1. Smaller clearances than those specified In table 22 are not allowed.

  CATALOGO FERODO MOTO PDF

Standard Detayı

Solder tsafh at ‘C. During the test, no sustained arcing shall occur. Protection for safety — Chapter Generali requirements’ incorporating Amendment No. For these ratings, the following specimens are used: Clearance is the shortest direct air path over the top of the barrier.

The variable control, if any, is set at the position of maximum output with any by-pass In open position. The heating test should be condLiCted at the highest applicable current lating applicable to the selected contact type each t’me T,3,6 Co-ordinated e.

Care shall be taken that the results from one series of three blows do not influence subsequent series. NOTE 2 No minimum thickness is specified for functional, basic, inaccessible supplementary and Inaccessible reinforced insulation.

With the exception of the luminosity which can be disregarded, the lamp shall function unless otherwise specified. After the test, the electronic switch shall be in the original state and’ the setting shall be unchanged.

Previous post: