ATMEGA Datasheet PDF Download – 8-bit Microcontroller, ATMEGA data sheet. Typical values contained in this datasheet are based on simulations and characterization . The ATmega is % pin compatible with ATmega, and can. ATMEGA 8-bit Microcontroller With 16k Bytes In-system Programmable Flash Features. High-performance, Low-power AVR® 8-bit Microcontroller Advanced.

Author: Nakora Gulmaran
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Finance
Published (Last): 16 July 2007
Pages: 336
PDF File Size: 8.65 Mb
ePub File Size: 10.27 Mb
ISBN: 398-1-62992-413-7
Downloads: 94186
Price: Free* [*Free Regsitration Required]
Uploader: Neshicage

Avoid using the SPM instruction. The Company assumes no responsibility for any errors. The following features have been added: Other terms and product names may be the trademarks of others Printed on recycled paper. Some of the fuses are described further in the following sections.

【ATMEGA161-8PU ATMEL】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

No licenses to patents or other intellectual property of Atmel dataseet granted by the Company in connection with the sale of Atmel products, expressly or by implication. The timing requirements for Parallel Programming have been changed. Pointer addresses external memory. No licenses to patents or other intellectual property of Atmel are granted.

See the ATmega data sheet for details. Programming Interface The Parallel Programming algorithm is changed. In C, the only construct that will.


Winslow ADAPTICs :: Solder Down Interface Modules – Device Specific :: WSDF

TEL 1 Refer atmeya161 data sheet for details. Make sure this issue is not harmful to the application. Atmel Corp oration Note that since the crystal oscillator in ATmega does not have a rail-to-rail amplitude, it is not possible to clock other units directly from the XTAL2 pin. FAX 1 Otherwise the system oscillator will continue to run, drawing additional current.

DataSheetDirect – catalog listing “A” no 24

Atmdga161 Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty. The ATmega has two operating modes selected through the fuse settings.

Otherwise, the error status will be lost. This means that the following six Interrupt Vectors disappears, and vectors from number 11 to 28 moved up to become vectors number 5 to Refer to the data sheet for ATmega for further information. Atme l Headquarte rs.

The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or atmegq161 detailed herein at any time without notice, and does not make any commitment to update the information contained herein.

AVR082 Replacing ATmega161 by ATmega162

In assembly, insert a nop instruction immediately after a loop to itself. If these status bits were cleared by writing 0xFF to the register in ATmega, this may trigger incorrect behavior when ported to ATmega, since the new control bits will be set. Increased Interrupt Latency In ATmega, all instructions are interruptable, and no dead-lock situation exists if a loop is followed by a two-word instruction for the purpose of looping until an atmega1611 goes active.


Other terms and product names may be the trademarks of others. Atmel’s products are not authorized for use as critical.

Check the data sheet for detailed information. It is called AS0 elsewhere in that data sheet, as well as everywhere in ATmega Use external Brown-out Detector and do not enable internal Brown-out Detector. When the compatibility mode is used, only non-conflicting enhancements make the part different from the ATmega The following bits have changed locations, but have the same functionality when accessed as in ATmega In this device, some instructions are not interruptable, and will cause the interrupt.

The following features are not supported when the ATmega is used in the ATmega compatibility mode:

Previous post: